### 1465

Low-cost gradients using commercially-available printed circuit boards
Junpei Matsuzaki1, Tomoyuki Haishi2, and Yasuhiko Terada1

1Institute of Applied Physics, Tsukuba, Japan, 2MRTechnology Inc., Tsukuba, Japan

### Synopsis

Gradient coils often need expensive, manufacturing processes such as gluing, etching, and/or milling. The purpose of this study is to propose low-cost gradients using commercially-available printed circuit boards (PCBs). For proof of concept, we fabricated four types of PCB-gradients for different MRI systems: cylindrical transverse gradients for a 1.5 T, 280 mm-bore superconducting magnet (SCM), for a 4.7 T, 89 mm-bore SCM, and for a 9.4 T, 54 mm-bore SCM, and planar gradients for a 0.2 T, 160 mm-gap permanent magnet. We verified that the PCB gradients outperform the hand-wound gradients.

### INTRODUCTION

Gradient coils are often constructed using solid or hollow copper winding wires, or using cuts in a continuous copper surface. Gradient coils needs to satisfy different requirements such as the high mechanical stiffness, the high-voltage isolation between the different layers, and a sufficient thermal conductivity, and thus they often need expensive, manufacturing processes such as gluing, etching, and/or milling. Here we propose low-cost gradients using commercially-available printed circuit boards (PCBs). We fabricated four types of PCB-gradients for different MRI systems, and evaluated the performance of the PCB gradients.

### METHODS

We fabricated four type of PCB-gradients: cylindrical transverse gradients for a 1.5 T, 280 mm-bore SCM (type A), for a 4.7 T, 89 mm-bore SCM (type B), and for a 9.4 T, 54 mm-bore SCM (type C), and planar gradients for a 0.2 T, 160 mm-gap permanent magnet (type D). We edited coil winding patterns, converted them to a drawing exchange format (DXF), and passed an order to an e-commerce company (p-ban.com [1]). The company fabricated flat-type PCBs according to the DXF data. The specification of the PCBs was listed in Fig. 1. The production costs were $2k (type A; x and y),$1.5k (type B; x and y), $10k (type C; x and y), and$40k (type D; x, y, and z).

Fabrication of cylindrical gradients (A, B, and C): The fabrication process of the type A gradient was shown in Fig. 2. The supplied PCBs were bent manually using a bending machine, and stacked together. The type A gradient had a large diameter, so the bent PCBs were fixed onto an acrylic pipe to ensure the high stiffness. After wiring, each PCB gradient was firmly fixed using an epoxy resin. The z gradient coils were fabricated by winding wires by hand onto the transverse PCB gradients.

Fabrication of planar gradients (D): x, y, and z PCB gradients were stacked, wired, and fixed firmly using an epoxy resin.

The performance of the type-A, PCB gradients was compared with that of a hand-wound gradient with the same winding pattern. Gradient impulse response functions (GIRFs) of the two gradients were measured using a field-camera system [2]. The image quality test was performed using a fast spin echo sequence (echo train length = 4, FOV = 64 mm x 64 mm, slice thickness = 10 mm; echo spacing = 40 ms, TE/TR = 40/2000 ms, matrix size = 256 x 256, bandwidth = 50 kHz; sequential ordering).

### RESULTS AND DISCUSSION

With this proof-of-concept study, we fabricated only transverse gradients for the cylindrical geometry. The longitudinal, cylindrical gradients using PCB boards have more electrical wire joints, and care needs to be taken to ensure high reliability of the electrical contacts.

### CONCLUSION

We fabricated the four-type PCB gradients for different MRI systems and verified the high performance of the PCB gradients.

### Acknowledgements

No acknowledgement found.

### References

[1] http://www.en.p-ban.com/

[2] Y. Kobayashi, K. Kose, and Y. Terada, “Development of a field camera system for a customized 1.5 T compact MRI system,” Proc. Intl. Soc. Mag. Reson. Med. 26, 4426, (2018)

### Figures

Fig. 1 Specifications of PCB gradients.

Fig. 2 Fabrication process of type-A gradient.

Fig. 3 Photos of PCB gradients.

Fig. 4 GIRFs of x and y gradients (type A).

Fig. 5 Phantom FSE images acquired with PCB and hand-wound gradients.

Proc. Intl. Soc. Mag. Reson. Med. 27 (2019)
1465